Demilec Wall Insulation Nationwide

Demilec Wall Insulation in Long Beach: What to Know First

We provide independent Demilec wall insulation service in Long Beach, with most jobs scheduled within 48 hours and completed in a single day. A typical drill-and-fill or injection foam job on a 1,200-square-foot home runs $2,800-$4,600, and we put that price in writing before any work starts. This page is for homeowners in Bixby Knolls, Belmont Heights, and the neighborhoods around Rancho Los Cerritos who already have Demilec spray foam or injection foam in their walls and need to know whether it can be repaired, supplemented, or replaced. Call (424) 415-7031 for a free estimate with a written price.

Call (424) 415-7031

How Demilec Products Fail - and How We Fix Them

• Demilec Sealection 500 shrinkage in cathedral ceilings. We see this in the 1920s bungalows off Atlantic Avenue, where open-cell foam installed 10-15 years ago has pulled away from rafter edges by 1/4 to 1/2 inch. The gap creates a thermal bypass that blower-door tests catch at the top plate. We remove the degraded foam, seal the rafter bays with closed-cell Demilec Heatlok HFO High Lift, and publish the before-and-after CFM50 so you see the actual air loss reduction.
• Demilec Heatlok Soya HFO water absorption in exterior walls. In Long Beach’s marine layer zones, particularly the blocks west of Lakewood Boulevard, soy-based open-cell foam can hold moisture against sheathing when the drainage plane behind stucco has failed. We don’t just re-foam; we run a moisture probe reading at multiple stud bays, replace any compromised sheathing, then switch to Heatlok HFO closed-cell at 2.5 inches minimum to create a vapor barrier the open cell couldn’t.
• Demilec Sealection Agribalance settling in drill-and-fill retrofit walls. Older homes in California Heights with lath-and-plaster often got Agribalance pumped through 5/8-inch holes that were never properly sealed. The foam settles 15-20 percent over five years, leaving a cold zone at the bottom of the stud bay. We extract the settled material with a vacuum hose, verify the bay is empty with a borescope, then reinstall at proper density with new plug seals that we photograph for the record.
• Demilec APX 500 adhesive failure on metal studs. Commercial retrofits near Long Beach Airport and the light industrial corridor sometimes used APX 500 on metal framing where surface prep was skipped. The foam delaminates in sheets. We grind to bare metal, apply a compatible primer, and use Heatlok XT for the reapplication because its adhesion to prepared metal has held up in our documented follow-ups.
• Demilec open-cell dusting and air leakage at electrical penetrations. In the tighter homes built 2015-2020 around the Traffic Circle, we find that Demilec Sealection 200 was sprayed before electricians finalized their rough-in. The foam gets carved away for outlet boxes and never resealed. We use a smoke pencil to find the leaks, pack them with backer rod and acoustic sealant, then add a targeted closed-cell cap where the wall meets the top plate. The blower-door number tells us if we got it all.

Our Demilec Wall Insulation Process

1. 1
   Schedule and scope. You call (424) 415-7031; a live person answers. We book a 90-minute window, send a text when the technician is en route, and arrive with a thermal camera and moisture meter.
2. 2
   Diagnostics and documentation. We measure existing R-values with a depth probe, run a blower-door test if air sealing is in scope, and photograph every wall section. You get a one-page report with pre-install readings before we quote.
3. 3
   Written price and parts call. We specify Demilec OEM foam or a compatible alternative from our multi-brand inventory, including Reflectix radiant barrier where it solves a problem foam can’t. The price is flat; the scope is written; the warranty is attached. No work starts until you have all three.
4. 4
   Prep and air sealing. Top plates, can lights, and penetrations get sealed before any new insulation goes in. Measure first, then insulate - otherwise you’re just trapping the problem.
5. 5
   Installation and verification. We install to the specified depth, take post-install depth readings and photos, and run a final blower-door test on jobs where air sealing was part of the scope. The photo record and test results go to you same day.
6. 6
   Cleanup and follow-up. HEPA vacuum, protective sheet removal, and a 365-Day Done Right Promise in writing. We call at 30 days to ask if the wall temperature feels different, but the blower-door number already told us the answer.

What Demilec Wall Insulation Costs in Long Beach

These are real numbers for Long Beach homes we’ve worked on, not teaser rates. The only way to move off these ranges is to see your walls. Call (424) 415-7031 for a free estimate with a written price before any work starts.

Why Long Beach Homeowners Call Topside Attic Insulation Long Beach for Demilec Work

We’ve been sealing and insulating homes under The Haven Standard since 2016, and we publish blower-door numbers on every job where air sealing applies. That matters for Demilec work because the foam is only as good as the envelope around it. Wes Okafor learned the trade at Olive-Harvey College in Chicago, where blower-door testing came before any insulation work, and that sequence hasn’t changed. Our technicians are background-checked, uniformed, and trained on Demilec’s specific cure times and adhesion requirements, not generic spray foam. We also stock Reflectix and other brands, so if your wall problem is better solved with a hybrid approach, we’ll say so in the written scope. Calls are answered by a live person 24/7. The 365-Day Done Right Promise applies to everything we touch.

FAQs