Demilec Insulation Removal & Replacement Nationwide

Demilec Insulation Removal & Replacement in Long Beach: What to Know First

We provide independent Demilec insulation removal and replacement in Long Beach, typically completing attic jobs in one to two days with same-day assessment availability. Most Demilec removal and replacement jobs in a Long Beach home this size run between $2,800 and $6,400 depending on contamination level, access, and whether the existing foam needs full extraction or targeted replacement. We do not start work without a written price, and we do not quote from photos alone.

Call (424) 415-7031

This page is for homeowners in Long Beach neighborhoods from Bixby Knolls to the Rancho Los Cerritos area who have Demilec spray foam or hybrid insulation that has failed, been contaminated, or was installed over an unsealed attic floor. If you are comparing written estimates or need a second opinion on a Demilec removal scope, call us at (424) 415-7031. Estimates are free, and we will read your existing quote with you line by line.

How Demilec Products Fail - and How We Fix Them

• Demilec Heatlok HFO High Lift - off-ratio curing in Long Beach marine air. The HFO blowing agent in Heatlok HFO High Lift is hydrophilic; when Long Beach’s morning marine layer pushes attic humidity above 70 percent during install, the A-side and B-side can cure off-ratio, leaving a tacky, crumbly surface that traps moisture against roof decking. We see this in Belmont Shore homes with late-summer installs. Our fix: full removal of the compromised lift, moisture mapping with a thermal camera, drying to below 16 percent wood moisture content, then reinstallation with documented ratio verification on every pass.
• Demilec Heatlok XT - thermal drift and R-value loss in cathedral ceilings. Heatlok XT was specified for many Long Beach 1920s bungalow cathedral ceilings because of its nominal R-6 per inch, but when installed over unvented rafter bays without proper air sealing at the ridge beam, convective looping pulls conditioned air through the foam interface. The result: thermal drift measured at 15 to 20 percent below labeled R-value within five to seven years. We remove the degraded XT, seal the ridge and soffit junctions with closed-cell at the critical transitions, then reinstall to depth with blower-door verification.
• Demilec Sealection 500 - rodent saturation and biological loading. Sealection 500’s open-cell structure is an excellent air barrier but a poor deterrent to roof rats, which have proliferated in Long Beach’s park-adjacent neighborhoods since 2019. Once rodents nest in Sealection 500, the urine load degrades the polymer and creates a persistent ammonia source. We see this in homes backing onto Recreation Park and El Dorado Park. Our fix: full extraction of contaminated foam, enzymatic treatment of the substrate, rodent proofing of all attic penetrations, then replacement with a closed-cell or hybrid assembly at the floor line where appropriate.
• Demilec Heatlok Soya - density failure from UV exposure in skylight wells. Heatlok Soya, marketed for its bio-based content, can experience surface chalking and density reduction when installed in skylight chases where reflected UV exceeds 500 microwatts per square centimeter. The foam does not fail structurally, but the degraded surface becomes a dust source and loses its air-barrier continuity. We remove the affected Soya in the chase, apply a UV-stable coating or thermal barrier where code requires, and reinstall with a compatible closed-cell product that maintains density under cyclic UV loading.
• Demilec open-cell hybrids - vapor retarder misalignment in mixed-dry/mixed-humid zones. Long Beach sits at the edge of California’s mixed-dry and mixed-humid climate zones. Demilec open-cell assemblies installed without a calculated vapor retarder - or with a retarder placed on the wrong side of the assembly - can accumulate interstitial moisture during winter interior humidity spikes. We remove the failed assembly, calculate the proper vapor retarder location using ASHRAE 160 methodology, reinstall with the correct sequence, and document the assembly with photos and a written moisture management plan.

Our Demilec Insulation Removal & Replacement Process

1. 1
   On-site assessment with thermal imaging and moisture mapping. We arrive with a written appointment time and text when en route. Wes Okafor or a named technician measures existing foam depth, identifies the Demilec product line by visual characteristics and density testing, and documents pre-condition photos. We run a blower-door test if the attic is connected to conditioned space - a pressurization reading that shows, in one number, how much air the building envelope is losing.
2. 2
   Written scope and price before any work starts. Under Haven Standard Clause 1, you receive a flat price, written scope, and written warranty before anyone lifts a tool. No exceptions. If you have a competing estimate, we provide a Free Second Opinion and read it with you.
3. 3
   Controlled removal with HEPA containment and substrate assessment. We set up negative air and HEPA filtration for all Demilec removals. The existing foam is mechanically removed to bare substrate; we do not leave crumbly residue that traps future moisture. Wood moisture content and substrate integrity are recorded.
4. 4
   Air sealing before any new insulation. We seal top plates, can lights, pipe penetrations, and chimney chases before any replacement product goes in. Measure first, then insulate - otherwise you’re just trapping the problem.
5. 5
   Replacement with OEM-compatible or specified alternative materials. We source materials from Demilec, Icynene, and other named manufacturers - no proprietary lock-in. The replacement product is selected for the specific assembly and climate load, not for margin.
6. 6
   Post-work documentation: photos, blower-door comparison, written record. You receive a Documented Photo Record on every visit, and on applicable jobs, before-and-after blower-door numbers so you can verify the air-sealing result. The 365-Day Done Right Promise applies to all completed work.

What Demilec Insulation Removal & Replacement Costs in Long Beach

Most Demilec insulation removal and replacement jobs in Long Beach run between $2,800 and $6,400. The price moves based on four factors: square footage of affected area, contamination level (clean removal versus rodent or mold remediation), access difficulty (cathedral ceilings and tight crawl spaces take longer), and whether the existing foam is a single lift or multi-layer assembly requiring full-gut extraction.

We do not price from satellite imagery or phone descriptions. Every written price follows a site visit. Call (424) 415-7031 to schedule - estimates are free, and you will have the number in writing before we leave.

Why Long Beach Homeowners Call Topside Attic Insulation Long Beach for Demilec Work

We are an independent Demilec service provider - not affiliated with or authorized by Demilec - which means we evaluate every job on its technical merits, not on warranty territory or brand loyalty. Our technicians are background-checked and uniformed; calls are answered by a live person 24/7, not a voicemail loop with callback windows measured in business days.

Since 2016, we have sealed and insulated over 9,000 homes, every one with a written price before work started and a documented record when the crew left. We also service Reflectix and other insulation systems, so if your Long Beach home has a hybrid assembly or a previous contractor mixed brands, we do not need to subcontract the diagnosis. The 365-Day Done Right Promise applies to all completed work. If it is not done right, we make it right - backed by a written scope and written warranty delivered before anyone starts.

FAQs